| Customization: | Available |
|---|---|
| Type: | FTTX Solutions |
| Certification: | CE, ISO, RoHS |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
DESCRIPTION
Application:
A type of dome closure series, used for direct connection during optical fiber transmission process, and provides joint connection protection, with 6 small round cable holes and 1 large cable hole; heat sealing with heat shrinkable casing; can be used for overhead, pole, wall and buried installations. With good sealing performance, the simple installation and wide application range are the best choice for optical fiber connection.
Product Feature:
All functional indicators are in line with the national YD 814.1-2004 standard for distribution box.
Four-in and four-out cable ports; there are 1 large and 6 small
circular holes, which can enter and exit the Φ7~Φ20 optical cables.
The outer box body is made of high-strength engineering plastics, It has features of light weight, high mechanical strength, anti aging, strong corrosion resistance, lightning resistance, and long service life.
Stacked structure splice tray and independent insulation grounding device make the optical fiber core configuration, expansion and the cable grounding flexible, convenient and safe.
The splice tray is equipped with splicing slots and a PLC splitter holder, which can be configured at any time according to the needs of direct or divergent connection.
Technical Index:
Fiber radius of curvature: ≥40mm
Optical disk additional loss: ≤ 0.01dB
Temperature Range: - 40°C ~ + 70°C
Anti lateral pressure: ≥2000N / 10 cm
Shock resistance: ≥20N.m
PRODUCT SPECIFICATION:
| Type | PG-FOSC-HJ2309M7 |
| Size(mm) | ¢230 * 320 |
| splitter type | 1:4(2pc)/1:8(2pc) |
| Cable diameter (mm) | ¢7~¢12 |
| Splice tray capacity | 16 (single core) |
| Max quantity of splice tray | 9 |
| Max capacity | 144 (single core) |
| Sealing type | heat shrinkable tube, silicon rubber |
| Protection level | IP68 |
INSTALLATION PROCESS
1. Cable installation
Open the hole:Saw the entry ports as needed.
Clean the cable sheath with cloth(about 1.8 meter) Slide the cable into the box through the hole.
2. Cable preparation
Strip the cable sheath, clean the filing, cut the cable reinforced core at 75mm distance from the sheath cut
If a shielded cable is installed, leave a cable shielding layer of approximately 25mm x 25mm in the axial direction at the annular cutout of the cable and clamp the shielded cable
Cut off the loose tube at 35mm from the annular section of the optical cable, remove the oil on the optical fiber bundle, put on the bare fiber protection tube.
Align the cable section and the base hole end, insert the reinforced core into the fixing hole, squeeze it with a nut and cut off the excess
If shield wire is used to connect 2 cables, the cables should be paired together according to the outlet order.
3. Oval hole sealing
Wipe the elliptical surface and cable sheath with a clean piece of paper or cloth to a distance of 100mm from the edge of the hole
Rough the elliptical surface and cable sheath with sand paper, clean them with cloth;
Put on the elliptical heat shrinkable tube, and mark the optic cable on the end of the tube; make the 2nd mark on the cable at 5mm from the 1st marker
Wrap the cable with warm aluminum paper from the 2nd mark
When install the 2nd cable, allocate the heat shrinkable tube according to the cable size, insert the branch card (note: all the branch cards should be fully inserted into the heat shrink tube)
Heat the heat shrink tube with a torch so that it shrinks all over the holder and cable, then heat the clips on both sides until the hot melt flows out of the two cables.
Shenzhen Pioneergoods Communication Co., Ltd., established in 2009 and located in Shenzhen,specializes in R&D, production, sales, and technical services for fiber telecom equipment and FTTH solutions. As a leading pro-vider in China, we offer two main product lines:Opticl Fiber Cable: Armored Fiber Optic cable/Duct Fiber Optic cable/Aerial Fiber optic Cable/Direct Buried Fiber Optic cable/Figure 8 Fiber Optic cable/Underwater Fiber Optic cable/ADSS Fiber Optic cableOptical cable installation hardware: Profession-al hardware for indoor and outdoor installation of optical cable, to provide you with a full range of solutions to install optical cable.We prioritize quality, im-plementing a comprehensive control svstem to ensure all products meet the highest standards. From raw materials to delivery, our professional team oversees every step to guarantee excellence. Trusted by global clients like Belden, STC, and Telefonica, we also provide OEM services tailored to cus-tomer needs.At POGOODS, we value customer satisfaction, fostering inno-vation, quality, and efficiency. Choose us for reliable solutions and mutual success.
Q1: Wonder if you accept small orders?
A1: Do not worry. Feel free to contact us .in order to get more orders and give our clients more convener ,we accept small order.
Q2: Can you send products to my country?
A2: Sure, we can. If you do not have your own ship forwarder, we can help you.
Q3: Can you do OEM for me?
A3: We accept all OEM orders,just contact us and give me your design.we will offer you a reasonable price and make samples for you ASAP.
Q4: What's your payment terms ?
A4: By T/T,LC AT SIGHT,30% deposit in advance, balance 70% before shipment.
Q5: How can I place the order?
A5: First sign the PI,pay deposit,then we will arrange the production.After finished production need you pay balance. Finally we will ship the Goods.
Q6: When can I get the quotation ?
A6: We usually quote you within 24 hours after we get your inquiry. If you are very urgent to get the quotation.Please call us or tell us in your mail, so that we could regard your inquiry priority.
){kind=link}