10gbps 20km SFP Fiber Optical Transceiver

Product Description

 

Product Description

 

 

Product Features
Up to 10Gbps data links

20km with 9/125µm SMF

1310nm DFB laser

Duplex LC Connector

Hot-pluggable SFP+ footprint            

Single 3. 3V power supply             

Operating temperature: 0ºC to 70ºC    Ethernet

RoHS                             

Digital Diagnostic Monitor compatible

Power Consumption < 0.8W

Applications
√  10GBase-LR/LW 10G
√  1200-SM-LL-L 10G FC


 

1. Product Description
The PGSFPP1310GLR is a 10Gbps enhanced small form factor pluggable SFP+ transceiver compatible with 10GBASE-LR/LW and 10G Fiber Channel 1200-SM-LL-L. It is suitable for single-mode fiber (SMF) communications in 10Gbps Ethernet and 10G Fiber Channel.
2. Regulatory Compliance
PIONEERGOODS transceivers are Class 1 Laser Products comply with FDA regulations. Meet Class 1 eye safety requirements of EN 60825 and the electrical safety requirements of EN 60950.
3. Absolute Maximum Ratings

Parameter	Symbol	Min.	Max.	Unit
Supply Voltage	VCC	-0.5	4	V
Storage Temperature	TS	-40	85	°C
Operating Case Temperature	TC	0	70	°C

4. Recommended Operating Conditions

Parameter	Symbol	Min.	Typical	Max.	Unit
Operating Case Temperature	TC	0		70	°C
Power Supply Voltage	VCC	3.15	3.3	3.45	V
Power Supply Current	ICC			200	mA
Data Rate			10		GBps
Max Link Length on 9/125µm SMF	Lmax		10		km

 

Parameter	Symbol	Min.	Typical	Max.	Unit
Transmitter
Centre Wavelength	λc	1260	1310	1360	nm
Spectral Width (-20dB)	σ			1	nm
Average Output Power	Pout	-5		0	dBm
Extinction Ratio	ER	3.5			dB
Average Launch Power of Off Transmitter	Poff			-30	dBm
Receiver
Centre Wavelength	λc	1200	1310	1600	nm
Receiver Sensitivity	PIN			-14	dBm
Receiver Overload	Pmax	0.5			dBm
LOS De-Assert	LOSD			-20	dBm
LOS Assert	LOSA	-23			dBm
LOS Hysteresis		0.5		4.5	dB

5. Optical Characteristics
6. Electrical Characteristics

Parameter	Symbol	Min.	Typical	Max.	Unit
Transmitter
Input Differential Impedance	Zin	90	100	110	Ω
Data Input Swing Differential	Vin	250		1200	mV
Tx-Dis Disable	Vd	2.0		Vcc	V
Tx-Dis Enable	Ven	0		0.8	V
Receiver
Data Output Swing Differential	Vout	250		800	mV
Rx-Los Fault	Vlf	2.0		VccHOST	V
Rx-Los Normal	Vln	0		0+0.8	V
Output rise and fall time	Tr, Tf	30			ps

7. Pin Descriptions

Pin	Symbol	Description	Ref.
1	VEET	Transmitter Ground  (Common with Receiver Ground)	7.1
2	TFAULT	Transmitter Fault. Not supported.
3	TDIS	Transmitter Disable. Laser output disabled on high or open.	7.2
4	MOD_DEF(2)	Module Definition 2. Data line for Serial ID.	7.3
5	MOD_DEF(1)	Module Definition 1. Clock line for Serial ID.	7.3
6	MOD_DEF(0)	Module Definition 0. Grounded within the module.	7.3
7	RS0	Rate Select0, optionally controls SFP+ module receiver. When high input signaling rate>4.25 GBd and when low input signaling rate<4.25GBd
8	LOS	Loss of Signal indication.  Logic 0 indicates normal operation.	7.4
9	RS1	Rate Select1, optionally controls SFP+ module receiver. When high input signaling rate>4.25 GBd and when low input signaling rate<4.25GBd
10	VEER	Receiver Ground  (Common with Transmitter Ground)	7.1
11	VEER	Receiver Ground  (Common with Transmitter Ground)	7.1
12	RD-	Receiver Inverted DATA out.  AC Coupled.
13	RD+	Receiver Non-inverted DATA out.  AC Coupled.
14	VEER	Receiver Ground  (Common with Transmitter Ground)	7.1
15	VCCR	Receiver Power Supply
16	VCCT	Transmitter Power Supply
17	VEET	Transmitter Ground  (Common with Receiver Ground)	7.1
18	TD+	Transmitter Non-Inverted DATA in.  AC Coupled.
19	TD-	Transmitter Inverted DATA in.  AC Coupled.
20	VEET	Transmitter Ground  (Common with Receiver Ground)	7.1

Notes:
7.1 Circuit ground is internally isolated from chassis ground.
7.2 Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
7.3 Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in.
7.4 LOS is open collector output.  Should be pulled up with 4.7k -10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.


8. EEPROM & DDM THRESHOLD
8.1 EEPROM
2 wire address 1010000X (A0h)
 

0~95
Serial ID Defined by SFP MSA (96 bytes)

96~127
Vendor Speific (32 bytes)

128~255
Reserved (128 bytes)

8.1 DDM THRESHOLD
 

	Low Alarm	Low Warn	High Warn	High Alarm
Temperature	-5ºC	0ºC	70ºC	75ºC
Voltage	3V	3.1V	3.6V	3.7V
Tx Bias	15mA	20mA	75mA	80mA
Tx Power	-12dBm	-8dBm	0.5dBm	3.5dBm
Rx Power	-18dBm	-16dBm	0.5dBm	3.5dBm

9. Mechanical Specifications

Ordering Information

Part No.	Data Rate	DDM	Wave	Fiber Type	Dist.	Temp.	Optical Interface
PGSFPP1310GLR	10Gbps	yes	1310nm	SMF	20km	0~70ºC	LC

VERSION UPDATE:

VERSION NO.	DATE	UPDATED INFORMATION
V20160818	20160818	EEPROM& DDM Threshold updated "LABEL" added Ordering information updated Product picture updated

NOTICE:
PIOGOODS reserves the right to make changes to this product in this specification without notice, in order to improve product performance.







Shenzhen Pioneergoods Communication Co., Ltd., established in 2009 and located in Shenzhen,specializes in R&D, production, sales, and technical services for fiber telecom equipment and FTTH solutions. As a leading pro-vider in China, we offer two main product lines:Opticl Fiber Cable: Armored Fiber Optic cable/Duct Fiber Optic cable/Aerial Fiber optic Cable/Direct Buried Fiber Optic cable/Figure 8 Fiber Optic cable/Underwater Fiber Optic cable/ADSS Fiber Optic cableOptical cable installation hardware: Profession-al hardware for indoor and outdoor installation of optical cable, to provide you with a full range of solutions to install optical cable.We prioritize quality, im-plementing a comprehensive control svstem to ensure all products meet the highest standards. From raw materials to delivery, our professional team oversees every step to guarantee excellence. Trusted by global clients like Belden, STC, and Telefonica, we also provide OEM services tailored to cus-tomer needs.At POGOODS, we value customer satisfaction, fostering inno-vation, quality, and efficiency. Choose us for reliable solutions and mutual success.




Q1: Wonder if you accept small orders?
Al: Do not worry. Feel free to contact us .in order to get more orders andgive our clients more convener ,we accept small order.

Q2: Can you send products to my country?
A2: Sure, we can. lf you do not have your own ship forwarder, we can help you.

Q3: Can you do OEM for me?
A3: We accept all OEM orders,just contact us and give me your design.we will offer you a reasonable price and make samples for you ASAP.

Q4: What's your payment terms ?
A4: By T/T,LC AT SIGHT,30% deposit in advance, balance 70% before shipment.

Q5: How can l place the order?
A5: First sign the Pl,pay deposit,then we will arrange the production.Afterfinished production need you pay balance. Finally we will ship the Goods.

Q6: When can l get the quotation ?
A6: We usually quote you within 24 hours after we get your inquiry. lf youare very urgent to get the quotation,Please call us or tell us in your mail, so that we could regard your inquiry priority.