Product Features
Up to 10Gbps data links
300m with 50/125µm 2000MHz MMF
850nm VCSEL laser
Duplex LC Connector
Hot-pluggable SFP+ footprint
Single 3. 3V power supply
Operating temperature: 0ºC to 70ºC
RoHS
Digital Diagnostic Monitor(DDM)
Power Consumption < 0.8W
Applications
√ 10GBase-SR/SW 10G Ethernet
1. Product Description
The PG-SFPP8510GSR is a 10Gbps enhanced small form factor pluggable SFP+ transceiver compatible with 10GBASE-SR/SW. It is suitable for multi-mode fiber (MMF) communications in 10Gbps Ethernet.
2. Regulatory Compliance
PIOGOODS transceivers are Class 1 Laser Products comply with FDA regulations. Meet Class 1 eye safety requirements of EN 60825 and the electrical safety requirements of EN 60950.
3. Absolute Maximum Ratings
| Parameter |
Symbol |
Min. |
Max. |
Unit |
| Supply Voltage |
VCC |
-0.5 |
4 |
V |
| Storage Temperature |
TS |
-40 |
85 |
°C |
| Operating Case Temperature |
TC |
0 |
70 |
°C |
4. Recommended Operating Conditions
| Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
| Operating Case Temperature |
TC |
0 |
|
70 |
°C |
| Power Supply Voltage |
VCC |
3.15 |
3.3 |
3.45 |
V |
| Power Supply Current |
ICC |
|
|
200 |
mA |
| Data Rate |
|
|
10 |
|
GBps |
| Max Link Length on 50/125µm 2000MHz MMF |
Lmax |
|
|
300 |
m |
5. Optical Characteristics
| Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
| Transmitter |
| Centre Wavelength |
λc |
840 |
850 |
860 |
nm |
| Spectral Width (RMS) |
σ |
|
|
0.5 |
nm |
| Average Output Power |
Pout |
-5 |
|
0 |
dBm |
| Extinction Ratio |
ER |
3.5 |
|
|
dB |
| Average Launch Power of Off Transmitter |
Poff |
|
|
-30 |
dBm |
| Receiver |
| Centre Wavelength |
λc |
840 |
850 |
860 |
nm |
| Receiver Sensitivity |
PIN |
|
|
-13 |
dBm |
| Receiver Overload |
Pmax |
0.5 |
|
|
dBm |
| LOS De-Assert |
LOSD |
|
|
-16 |
dBm |
| LOS Assert |
LOSA |
-18 |
|
|
dBm |
| LOS Hysteresis |
|
0.5 |
|
|
dB |
6. Electrical Characteristics
| Parameter |
Symbol |
Min. |
Typical |
Max. |
Unit |
| Transmitter |
| Input Differential Impedance |
Zin |
90 |
100 |
110 |
Ω |
| Data Input Swing Differential |
Vin |
200 |
|
700 |
mV |
| Tx-Dis Disable |
Vd |
2.0 |
|
Vcc |
V |
| Tx-Dis Enable |
Ven |
0 |
|
0.8 |
V |
| Receiver |
| Data Output Swing Differential |
Vout |
300 |
|
800 |
mV |
| Rx-Los Fault |
Vlf |
2.0 |
|
VccHOST |
V |
| Rx-Los Normal |
Vln |
0 |
|
0+0.8 |
V |
| Output rise and fall time |
Tr, Tf |
28 |
|
|
ps |
7. Pin Descriptions
| Pin |
Symbol |
Description |
Ref. |
| 1 |
VEET |
Transmitter Ground (Common with Receiver Ground) |
7.1 |
| 2 |
TFAULT |
Transmitter Fault. Not supported. |
|
| 3 |
TDIS |
Transmitter Disable. Laser output disabled on high or open. |
7.2 |
| 4 |
MOD_DEF(2) |
Module Definition 2. Data line for Serial ID. |
7.3 |
| 5 |
MOD_DEF(1) |
Module Definition 1. Clock line for Serial ID. |
7.3 |
| 6 |
MOD_DEF(0) |
Module Definition 0. Grounded within the module. |
7.3 |
| 7 |
RS0 |
Rate Select0, optionally controls SFP+ module receiver. When high input signaling rate>4.25 GBd and when low input signaling rate<4.25GBd |
|
| 8 |
LOS |
Loss of Signal indication. Logic 0 indicates normal operation. |
7.4 |
| 9 |
RS1 |
Rate Select1, optionally controls SFP+ module receiver. When high input signaling rate>4.25 GBd and when low input signaling rate<4.25GBd |
|
| 10 |
VEER |
Receiver Ground (Common with Transmitter Ground) |
7.1 |
| 11 |
VEER |
Receiver Ground (Common with Transmitter Ground) |
7.1 |
| 12 |
RD- |
Receiver Inverted DATA out. AC Coupled. |
|
| 13 |
RD+ |
Receiver Non-inverted DATA out. AC Coupled. |
|
| 14 |
VEER |
Receiver Ground (Common with Transmitter Ground) |
7.1 |
| 15 |
VCCR |
Receiver Power Supply |
|
| 16 |
VCCT |
Transmitter Power Supply |
|
| 17 |
VEET |
Transmitter Ground (Common with Receiver Ground) |
7.1 |
| 18 |
TD+ |
Transmitter Non-Inverted DATA in. AC Coupled. |
|
| 19 |
TD- |
Transmitter Inverted DATA in. AC Coupled. |
|
| 20 |
VEET |
Transmitter Ground (Common with Receiver Ground) |
7.1 |
Notes:
7.1 Circuit ground is internally isolated from chassis ground.
7.2 Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V.
7.3 Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in.
7.4 LOS is open collector output. Should be pulled up with 4.7k -10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
8. EEPROM & DDM THRESHOLD
8.1 EEPROM
2 wire address 1010000X (A0h)
0~95
Serial ID Defined by SFP MSA (96 bytes) |
96~127
Vendor Speific (32 bytes) |
128~255
Reserved (128 bytes) |
8.1 DDM THRESHOLD
| |
Low Alarm |
Low Warn |
High Warn |
High Alarm |
| Temperature |
-14ºC |
-9ºC |
88ºC |
93ºC |
| Voltage |
2.9V |
3V |
3.6V |
3.7V |
| Tx Bias |
4mA |
5mA |
10.8mA |
11.8mA |
| Tx Power |
-6dBm |
-5dBm |
-1dBm |
0dBm |
| Rx Power |
-16dBm |
-14dBm |
-1dBm |
0dBm |
- Mechanical Specifications
10. LABEL
PIOGOODS offers label OEM design and print.
Label barcode supports code128 and 2D barcode
SIZE: 1) Front 35mm*10.5mm 2)Back 26mm*10.5mm
Ordering Information
| Part No. |
Data Rate |
DDM |
Wave |
Fiber Type |
Dist. |
Temp. |
Optical Interface |
| PG-SFPP8510GSR |
10Gbps |
yes |
850nm |
MMF |
300m |
0~70ºC |
LC |
VERSION UPDATE:
| VERSION NO. |
DATE |
UPDATED INFORMATION |
| V20160818 |
20160818 |
- EEPROM& DDM Threshold updated
- "LABEL" added
- Ordering information updated
- Product picture updated
|
| |
|
|
NOTICE:
PIOGOODS reserves the right to make changes to this product in this specification without notice, in order to improve product performance.
Shenzhen Pioneergoods Communication Co., Ltd., established in 2009 and located in Shenzhen,specializes in R&D, production, sales, and technical services for fiber telecom equipment and FTTH solutions. As a leading pro-vider in China, we offer two main product lines:Opticl Fiber Cable: Armored Fiber Optic cable/Duct Fiber Optic cable/Aerial Fiber optic Cable/Direct Buried Fiber Optic cable/Figure 8 Fiber Optic cable/Underwater Fiber Optic cable/ADSS Fiber Optic cableOptical cable installation hardware: Profession-al hardware for indoor and outdoor installation of optical cable, to provide you with a full range of solutions to install optical cable.We prioritize quality, im-plementing a comprehensive control svstem to ensure all products meet the highest standards. From raw materials to delivery, our professional team oversees every step to guarantee excellence. Trusted by global clients like Belden, STC, and Telefonica, we also provide OEM services tailored to cus-tomer needs.At POGOODS, we value customer satisfaction, fostering inno-vation, quality, and efficiency. Choose us for reliable solutions and mutual success.
Q1: Wonder if you accept small orders?
Al: Do not worry. Feel free to contact us .in order to get more orders andgive our clients more convener ,we accept small order.
Q2: Can you send products to my country?
A2: Sure, we can. lf you do not have your own ship forwarder, we can help you.
Q3: Can you do OEM for me?
A3: We accept all OEM orders,just contact us and give me your design.we will offer you a reasonable price and make samples for you ASAP.
Q4: What's your payment terms ?
A4: By T/T,LC AT SIGHT,30% deposit in advance, balance 70% before shipment.
Q5: How can l place the order?
A5: First sign the Pl,pay deposit,then we will arrange the production.Afterfinished production need you pay balance. Finally we will ship the Goods.
Q6: When can l get the quotation ?
A6: We usually quote you within 24 hours after we get your inquiry. lf youare very urgent to get the quotation,Please call us or tell us in your mail, so that we could regard your inquiry priority.
Audited Supplier 
){kind=link}